JOPSS - Search Results

Journal Articles

A Study on sodium-concrete reaction in presence of internal heating

Kawaguchi, Munemichi; Miyahara, Shinya*; Uno, Masayoshi*

Journal of Nuclear Engineering and Radiation Science, 6(2), p.021305_1 - 021305_9, 2020/04

Sodium-concrete reaction (SCR) is one of the important phenomena during severe accidents in sodium-cooled fast reactors (SFRs) owing to the generation of large sources of hydrogen and aerosols in the containment vessel. In this study, SCR experiments with an internal heater were performed to investigate the chemical reaction beneath the internal heater (800 $^{circ}$ C), which was used to simulate the obstacle and heating effect on SCR. Furthermore, the effects of the internal heater on the self-termination mechanism were discussed. The internal heater on the concrete hindered the transport of Na into the concrete. Therefore, Na could start to react with the concrete at the periphery of the internal heater, and the concrete ablation depth at the periphery was larger than under the internal heater. The high Na pool temperature of 800 $^{circ}$ C increased largely the Na aerosol release rate, which was explained by Na evaporation and hydrogen bubbling, and formed the porous reaction product layer, whose porosity was 0.54-0.59 from the mass balance of Si and image analyzing EPMA mapping. They had good agreement with each other. The porous reaction products decreased the amount of Na transport into the reaction front. The Na concentration around the reaction front became about 30wt.% despite the position of the internal heater. It was found that the Na concentration condition was one of the dominant parameters for the self-termination of SCR, even in the presence of the internal heater.

Journal Articles

Tritium confinement and detritiation demonstration program for fusion reactor rooms using caisson assembly for tritium safety study (CATS) at TPL/JAERI

Hayashi, Takumi; Kobayashi, Kazuhiro; Nishi, Masataka

Hoken Butsuri, 35(1), p.112 - 115, 2000/03

http://ci.nii.ac.jp/naid/10004466002

no abstracts in English

JAEA Reports

None

JNC TN1400 2000-001, 371 Pages, 2000/01

JNC-TN1400-2000-001.pdf:12.26MB

no abstracts in English

JAEA Reports

Preparation of methods to calculate pin-wise intra-subassembly power density distribution of a new in-pile experimental reactor for FBR safety research

Mizuno, Masahiro*; Uto, Nariaki

JNC TN9400 98-007, 147 Pages, 1998/11

JNC-TN9400-98-007.pdf:8.32MB

A design study of a new in-pile experimental reactor, SERAPH (Safety Engineering Reactor for Accident PHenomenology), for FBR safety research has progressed at JNC (Japan Nuclear Cycle Development Institute). SERAPH is intended for various in-pile experiments to be performed under steady state and various transient operation modes. Heavy water is selected as a coolant material for heat removal of the SERAPH driver core during the experiments. Control rods are needed to conduct the experiments, and a control rod with heavy water follower is considered as one of the promising ideas and is now under investigation. In this idea, care must be taken to avoid production of local power peaks which are caused by neutron moderation in the follower and may appear in the vicinity of the boundary between the control rod and its neighboring fuel subassembly, since deuterium has an excellently high moderation power. Therefore, preparation of some methods of evaluating power density distribution in detail is required for control rod design. This report describes preparation of a set of neutronic calculation methods to evaluate intra-subassembly power density distribution including local power peaks around a control rod. A two-dimensional S $_{n}$ transport calculation code TWOTRAN-II is selected as a tool for evaluating neutron transport phenomena near the control rod with no cares for statistical influence. A two-dimensional rectangular super-cell model, which is a physical model composed of a control rod and its surrounding fifteen fuel sub-assemblies, and a method to construct the super-cell model based on thirteen unit cells are created, considering neutron mean free path near a control rod. Two processing tools are newly developed to generate a material region map and mesh boundaries for an efficient super-cell construction procedure and to obtain pin-wise power densities based on calculated mesh-wise neutron flux data. The results in this report are expected to be ...